今天小編給大家介紹下關于通風管道是如何降低噪音的:
Today, I'd like to introduce to you how ventilation ducts reduce noise:
一.降低通風設備聲源噪聲
I Reduce the sound source noise of ventilation equipment
（1）合理選擇通風設備的機型。在噪聲控制要求高的場合，應選用低噪聲通風設備。不同型號的通風設備在同意的風量、風壓下、機翼型葉片的離心通風設備噪聲小，前向版型葉片的離心通風設備噪聲大。
(1) Reasonably select the type of ventilation equipment. Low noise ventilation equipment shall be selected for occasions with high noise control requirements. Under the agreed air volume and pressure of different types of ventilation equipment, the noise of centrifugal ventilation equipment with wing blade is small, and the noise of centrifugal ventilation equipment with forward plate blade is large.
（2）通風設備的工作點應接近效率高點。同一型號的通風設備效率越高，噪聲越小。
(2) The working point of ventilation equipment shall be close to the high efficiency point. The higher the efficiency of ventilation equipment of the same model, the lower the noise.
（3）在可能條件下適當降低通風設備的轉速。通風設備的旋轉噪聲與葉輪圓周速度10次方成比例，渦流噪聲與葉輪圓周速度6次方（或5次方）成比例。故降低轉速可降低噪聲。
(3) If possible, reduce the speed of ventilation equipment appropriately. The rotating noise of ventilation equipment is proportional to the 10th power of impeller circumferential speed, and the eddy current noise is proportional to the 6th power (or 5th power) of impeller circumferential speed. Therefore, reducing the speed can reduce the noise.
（4）通風設備進、出口的噪聲級是通風理、風壓曾加加大。因此，設計通風系統時，應盡量減少系統的壓力損失。當通風系統的總量和壓力損失較大時，可將其分為小系統。
(4) The noise level at the inlet and outlet of ventilation equipment is that the ventilation principle and wind pressure have increased. Therefore, when designing the ventilation system, the pressure loss of the system should be minimized. When the total amount and pressure loss of the ventilation system are large, it can be divided into small systems.
（5）氣流在管道內的流速不宜過高，以免引起再次產生噪聲。確定管道內氣流流速應根據不同要求按有關規定選取。
(5) The flow rate of air flow in the pipeline should not be too high to avoid generating noise again. To determine the air flow velocity in the pipeline, it shall be selected according to different requirements and relevant regulations.
（6）注意通風設備與電動機的傳動方式。采用直聯傳動的通風設備噪聲小，用聯軸器的次之，用沒有接縫的三角皮帶傳動的稍差。通風設備應配用低噪聲的電動機。
(6) Pay attention to the transmission mode of ventilation equipment and motor. The ventilation equipment driven by direct coupling has low noise, followed by coupling, and the one driven by V-belt without joint is slightly worse. Ventilation equipment shall be equipped with low-noise motor.
二.傳遞途徑上對通風設備噪聲減小
II Reduce the noise of ventilation equipment in the transmission way
（1）在通風設備的進、出風口上裝配恰當?shù)南暺鳌?/div>
(1) Install proper mufflers on the air inlets and outlets of ventilation equipment.
（2）通風設備設減振基座，進、出風口用軟管連接。
(2) The ventilation equipment is equipped with a damping base, and the air inlet and outlet are connected with hoses.
（3）對通風設備做隔聲處理。如設備通風設備隔聲罩；在通風設備機殼內襯只聲材料；將通風設備設置在專門的通風設備室內，并設置隔聲門、隔聲窗或設置其他吸聲設施，或在通風設備室內另設值班室等。
(3) Make sound insulation treatment for ventilation equipment. Such as ventilation equipment and sound insulation cover; Lining the enclosure of ventilation equipment with acoustic materials; Set the ventilation equipment in the special ventilation equipment room, and set sound insulation doors, sound insulation windows or other sound-absorbing facilities, or set another duty room in the ventilation equipment room.
（4）通風設備室的進、排氣通道采取聲措施。
(4) Acoustic measures shall be taken for the inlet and exhaust channels of the ventilation equipment room.
（5）將通風設備布置在遠離要求安靜的房間。
(5) Place ventilation away from rooms requiring quiet.
三.及時維護通風管道保養，定期檢維護，及時更換破損零部件，排除異常，以創造低噪聲運行條件。
III Timely maintain the ventilation duct, conduct regular inspection and maintenance, timely replace damaged parts and eliminate abnormalities, so as to create low-noise operation conditions.
The above is the detailed introduction of Jinan ventilation duct. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.xyphw.com
上一篇：為什么使用螺旋風管比傳統矩形風管更加經濟
下一篇：商場中通風管道的用途是什么？
常見問題
PRODUCT
新聞推薦
NEWS
